Suche
Unten sind die Ergebnisse Ihrer Suche gelistet.
Volltextergebnisse:
- Asterisk Anbindung ans ISDN @voip:asterisk18
- crystalclock=(yes|no), watchdog=(yes|no) Port Attributes: mode=(te|nt), link=(ptp|ptmp), master... crystalclock=(yes|no), watchdog=(yes|no) Port Attributes: mode=(te|nt), link=(ptp|ptmp), optica... - - - - - Card Type: hfcmulti, avmfritz, w6692pci Port Attributes: mode=(te|nt), link=(ptp|ptmp), capi=(... - - - - - - Module: xhfc Options: debug=<number> Port Attributes: mode=(te|nt), link=(ptp|ptmp), line=(
- misdn-init.conf @voip:asterisk
- o run "/usr/sbin/misdn-init start" [ii] make your port (1) available in asterisk by editing "/etc/asteri... of the Master, then this port cannot # ye... rxclock - use clocking for pcm from ST Port # crystalclock - use clocking for p... transparent mode # # card=1,avmfritz # # Port settings # # Syntax: <port_type>=<port_number>[,<
- Asterisk Grundkonfiguration @voip:asterisk
- tt definieren wir erst einmal den Voicemailserver-Port und auch aktivieren die deutschen Sprachprompts. ... ult is yes) bindport=5060 ; UDP Port to bind to (SIP standard port for unencrypted UDP bindaddr=0.0.0.0 ; IP address to bind... ult is yes) bindport=5060 ; UDP Port to bind to (SIP standard port for unencrypted UDP
- Einrichten von Asterisk 14.x unter CentOS7 @voip:c7:asterisk14
- zone=internal --add-rich-rule="rule family="ipv4" port protocol="udp" port="4569" accept" success # firewall-cmd --reload success # firewall-cm... icmp-blocks: rich rules: rule family="ipv4" port port="4569" protocol="udp" accept </code> # firewall-cmd --get-active-zones <code>internal inter
- Asterisk Anbindung ans ISDN @voip:asterisk
- crystalclock=(yes|no), watchdog=(yes|no) Port Attributes: mode=(te|nt), link=(ptp|ptmp), master... crystalclock=(yes|no), watchdog=(yes|no) Port Attributes: mode=(te|nt), link=(ptp|ptmp), optica... - - - - - Card Type: hfcmulti, avmfritz, w6692pci Port Attributes: mode=(te|nt), link=(ptp|ptmp), capi=(... - - - - - - Module: xhfc Options: debug=<number> Port Attributes: mode=(te|nt), link=(ptp|ptmp), line=(
- Asterisk Grundkonfiguration @voip:asterisk18
- tt definieren wir erst einmal den Voicemailserver-Port und auch aktivieren die deutschen Sprachprompts. ... Dyn Forcerport ACL Port Status 12/12 (Unspe... ode> -- Registered SIP '14' at 192.168.10.61 port 5060</code> Eine erneute Abfrage der peers zeigt ... Dyn Forcerport ACL Port Status 12/12 (Unspe
- Fax-Server mit HylaFAX+ unter CentOS5 @voip:fax
- B Modem. Nach dem Anstecken des Modems an den USB-Port wird dies im syslog entsprechend quittiert: <code... n faxaddmodem to configure a modem [yes]? Serial port that modem is connected to []? modem Ok, time to... Modems: <code>Now we are going to probe the tty port to figure out the type of modem that is attached.... e that if you do not have the modem cabled to the port, or the modem is turned off, this may hang (just
- Installation und Konfiguration von mISDN
- o run "/usr/sbin/misdn-init start" [ii] make your port (1) available in asterisk by editing "/etc/asteri... tkonfiguration auszugeben: <code>misdnportinfo Port 1: TE-mode BRI S/T interface line (for phone lin... d, but not allowed for TE lib. -> childcnt: 2 * Port NOT useable for PBX (maybe there is already a PBX
- MySQL-Datenbankdefinitionen @voip:asterisk
- 80) NOT NULL, `ipaddr` varchar(15) NOT NULL, `port` smallint(5) unsigned NOT NULL default '0', `re... act | ipaddr | port | regserver | regseconds | username | MSN
- odbc.ini @voip:asterisk
- ost USER = Mark_Spencer PASSWORD = Mark_is_a_Geek PORT = 3306</code> Die beiden Parameter: * SERVER
- nützliche Kommandos rund um Asterisk @voip:asterisk18
- Dyn Forcerport ACL Port Status 12/12 (Unspe